Structuring of polymer surface by evaporation of sessile microdrops

In this thesis, we investigated the evaporation of sessile microdroplets on different solid substrates. Three major aspects were studied: the influence of surface hydrophilicity and heterogeneity on the evaporation dynamics for an insoluble solid substrate, the influence of external process parameters and intrinsic material properties on microstructuring of soluble polymer substrates and the influence of an increased area to volume ratio in a microfluidic capillary, when evaporation is hindered. In the first part, the evaporation dynamics of pure sessile water drops on smooth self-assembled monolayers (SAMs) of thiols or disulfides on gold on mica was studied. With increasing surface hydrophilicity the drop stayed pinned longer. Thus, the total evaporation time of a given initial drop volume was shorter, since the drop surface, through which the evaporation occurs, stays longer large. Usually, for a single drop the volume decreased linearly with t1.5, t being the evaporation time, for a diffusion-controlled evaporation process. However, when we measured the total evaporation time, ttot, for multiple droplets with different initial volumes, V0, we found a scaling of the form V0 = attotb. The more hydrophilic the substrate was, the more showed the scaling exponent a tendency to an increased value up to 1.6. This can be attributed to an increasing evaporation rate through a thin water layer in the vicinity of the drop. Under the assumption of a constant temperature at the substrate surface a cooling of the droplet and thus a decreased evaporation rate could be excluded as a reason for the different scaling exponent by simulations performed by F. Schönfeld at the IMM, Mainz. In contrast, for a hairy surface, made of dialkyldisulfide SAMs with different chain lengths and a 1:1 mixture of hydrophilic and hydrophobic end groups (hydroxy versus methyl group), the scaling exponent was found to be ~ 1.4. It increased to ~ 1.5 with increasing hydrophilicity. A reason for this observation can only be speculated: in the case of longer hydrophobic alkyl chains the formation of an air layer between substrate and surface might be favorable. Thus, the heat transport to the substrate might be reduced, leading to a stronger cooling and thus decreased evaporation rate. In the second part, the microstructuring of polystyrene surfaces by drops of toluene, a good solvent, was investigated. For this a novel deposition technique was developed, with which the drop can be deposited with a syringe. The polymer substrate is lying on a motorized table, which picks up the pendant drop by an upward motion until a liquid bridge is formed. A consecutive downward motion of the table after a variable delay, i.e. the contact time between drop and polymer, leads to the deposition of the droplet, which can evaporate. The resulting microstructure is investigated in dependence of the processes parameters, i.e. the approach and the retraction speed of the substrate and the delay between them, and in dependence of the intrinsic material properties, i.e. the molar mass and the type of the polymer/solvent system. The principal equivalence with the microstructuring by the ink-jet technique was demonstrated. For a high approach and retraction speed of 9 mm/s and no delay between them, a concave microtopology was observed. In agreement with the literature, this can be explained by a flow of solvent and the dissolved polymer to the rim of the pinned droplet, where polymer is accumulated. This effect is analogue to the well-known formation of ring-like stains after the evaporation of coffee drops (coffee-stain effect). With decreasing retraction speed down to 10 µm/s the resulting surface topology changes from concave to convex. This can be explained with the increasing dissolution of polymer into the solvent drop prior to the evaporation. If the polymer concentration is high enough, gelation occurs instead of a flow to the rim and the shape of the convex droplet is received. With increasing delay time from below 0 ms to 1s the depth of the concave microwells decreases from 4.6 µm to 3.2 µm. However, a convex surface topology could not be obtained, since for longer delay times the polymer sticks to the tip of the syringe. Thus, by changing the delay time a fine-tuning of the concave structure is accomplished, while by changing the retraction speed a principal change of the microtopolgy can be achieved. We attribute this to an additional flow inside the liquid bridge, which enhanced polymer dissolution. Even if the pendant drop is evaporating about 30 µm above the polymer surface without any contact (non-contact mode), concave structures were observed. Rim heights as high as 33 µm could be generated for exposure times of 20 min. The concave structure exclusively lay above the flat polymer surface outside the structure even after drying. This shows that toluene is taken up permanently. The increasing rim height, rh, with increasing exposure time to the solvent vapor obeys a diffusion law of rh = rh0  tn, with n in the range of 0.46 ~ 0.65. This hints at a non-Fickian swelling process. A detailed analysis showed that the rim height of the concave structure is modulated, unlike for the drop deposition. This is due to the local stress relaxation, which was initiated by the increasing toluene concentration in the extruded polymer surface. By altering the intrinsic material parameters i.e. the polymer molar mass and the polymer/solvent combination, several types of microstructures could be formed. With increasing molar mass from 20.9 kDa to 1.44 MDa the resulting microstructure changed from convex, to a structure with a dimple in the center, to concave, to finally an irregular structure. This observation can be explained if one assumes that the microstructuring is dominated by two opposing effects, a decreasing solubility with increasing polymer molar mass, but an increasing surface tension gradient leading to instabilities of Marangoni-type. Thus, a polymer with a low molar mass close or below the entanglement limit is subject to a high dissolution rate, which leads to fast gelation compared to the evaporation rate. This way a coffee-rim like effect is eliminated early and a convex structure results. For high molar masses the low dissolution rate and the low polymer diffusion might lead to increased surface tension gradients and a typical local pile-up of polymer is found. For intermediate polymer masses around 200 kDa, the dissolution and evaporation rate are comparable and the typical concave microtopology is found. This interpretation was supported by a quantitative estimation of the diffusion coefficient and the evaporation rate. For a different polymer/solvent system, polyethylmethacrylate (PEMA)/ethylacetate (EA), exclusively concave structures were found. Following the statements above this can be interpreted with a lower dissolution rate. At low molar masses the concentration of PEMA in EA most likely never reaches the gelation point. Thus, a concave instead of a convex structure occurs. At the end of this section, the optically properties of such microstructures for a potential application as microlenses are studied with laser scanning confocal microscopy. In the third part, the droplet was confined into a glass microcapillary to avoid evaporation. Since here, due to an increased area to volume ratio, the surface properties of the liquid and the solid walls became important, the influence of the surface hydrophilicity of the wall on the interfacial tension between two immiscible liquid slugs was investigated. For this a novel method for measuring the interfacial tension between the two liquids within the capillary was developed. This technique was demonstrated by measuring the interfacial tensions between slugs of pure water and standard solvents. For toluene, n-hexane and chloroform 36.2, 50.9 and 34.2 mN/m were measured at 20°C, which is in a good agreement with data from the literature. For a slug of hexane in contact with a slug of pure water containing ethanol in a concentration range between 0 and 70 (v/v %), a difference of up to 6 mN/m was found, when compared to commercial ring tensiometry. This discrepancy is still under debate.

Multiplex-Genotypisierung forensisch relevanter SNPs unter Verwendung von Microarrays auf chemisch aktivierten Glasflächen

Die Analyse tandem-repetitiver DNA-Sequenzen hat einen festen Platz als genetisches Typisierungsverfahren in den Breichen der stammesgeschichtlichen Untersuchung, der Verwandtschaftsanalyse und vor allem in der forensischen Spurenkunde, bei der es durch den Einsatz der Multiplex-PCR-Analyse von Short Tandem Repeat-Systemen (STR) zu einem Durchbruch bei der Aufklärung und sicheren Zuordnung von biologischen Tatortspuren kam. Bei der Sequenzierung des humanen Genoms liegt ein besonderes Augenmerk auf den genetisch polymorphen Sequenzvariationen im Genom, den SNPs (single nucleotide polymorphisms). Zwei ihrer Eigenschaften – das häufige Vorkommen innerhalb des humanen Genoms und ihre vergleichbar geringe Mutationsrate – machen sie zu besonders gut geeigneten Werkzeugen sowohl für die Forensik als auch für die Populationsgenetik.rnZum Ziel des EU-Projekts „SNPforID“, aus welchem die vorliegende Arbeit entstanden ist, wurde die Etablierung neuer Methoden zur validen Typisierung von SNPs in Multiplexverfahren erklärt. Die Berücksichtigung der Sensitivität bei der Untersuchung von Spuren sowie die statistische Aussagekraft in der forensischen Analyse standen dabei im Vordergrund. Hierfür wurden 52 autosomale SNPs ausgewählt und auf ihre maximale Individualisierungsstärke hin untersucht. Die Untersuchungen der ersten 23 selektierten Marker stellen den ersten Teil der vorliegenden Arbeit dar. Sie umfassen die Etablierung des Multiplexverfahrens und der SNaPshot™-Typisierungsmethode sowie ihre statistische Auswertung. Die Ergebnisse dieser Untersuchung sind ein Teil der darauf folgenden, in enger Zusammenarbeit der Partnerlaboratorien durchgeführten Studie der 52-SNP-Multiplexmethode. rnEbenfalls im Rahmen des Projekts und als Hauptziel der Dissertation erfolgten Etablierung und Evaluierung des auf der Microarray-Technologie basierenden Verfahrens der Einzelbasenverlängerung auf Glasobjektträgern. Ausgehend von einer begrenzten DNA-Menge wurde hierbei die Möglichkeit der simultanen Hybridisierung einer möglichst hohen Anzahl von SNP-Systemen untersucht. Die Auswahl der hierbei eingesetzten SNP-Marker erfolgte auf der Basis der Vorarbeiten, die für die Etablierung des 52-SNP-Multiplexes erfolgreich durchgeführt worden waren. rnAus einer Vielzahl von Methoden zur Genotypisierung von biallelischen Markern hebt sich das Assay in seiner Parallelität und der Einfachheit des experimentellen Ansatzes durch eine erhebliche Zeit- und Kostenersparnis ab. In der vorliegenden Arbeit wurde das „array of arrays“-Prinzip eingesetzt, um zur gleichen Zeit unter einheitlichen Versuchsbedingungen zwölf DNA-Proben auf einem Glasobjektträger zu typisieren. Auf der Basis von insgesamt 1419 typisierten Allelen von 33 Markern konnte die Validierung mit einem Typisierungserfolg von 86,75% abgeschlossen werden. Dabei wurden zusätzlich eine Reihe von Randbedingungen in Bezug auf das Sonden- und Primerdesign, die Hybridisierungsbedingungen sowie physikalische Parameter der laserinduzierten Fluoreszenzmessung der Signale ausgetestet und optimiert. rn